Đổ mực cho máy in phun màu


In this guide we will be showing you how to refill the majority of HP, Dell, Lexmark and Canon inkjet cartridges. Before following these instructions please take a moment to locate the relevant sub article from the gallery below so you know how much ink and where to inject it for your cartridge:

 

image
Canon Black PG-37/2145B001, PG-40/0615B001, PG-50/0616B001

image

Canon Black PG-37/2145B001, PG-40/0615B001, PG-50/0616B001

image

Canon Black PG-510/2970B001AA, PG-512/2969B001AA

image

Canon Colour CL-38/2146B001, CL-41/0617B001, CL-51/0618B001

 

Còn nhiều loại hộp mực khác cũng có thể làm như vậy.

Unfortunately if you do not see your cartridge above then this guide is not applicable but we should still be able to help here.

With this done make sure you have a syringe, the relevant colours of refill ink and plenty of tissue paper (kitchen paper recommended) before moving onto the instructions below:

1. Place the cartridge in question on some tissue paper somewhere that will be easy to clean if you should spill any ink.

2. Remove any labels from the top of the cartridge.

3. Use a syringe to suck up appropriate amount of ink for the cartridge in question.

4. Poke the needle the into relevant hole and roughly half deep into the sponge. Wehere possible use the hole closest to the printhead for best results, especially with black only ink cartridges.

image
5. Slowly inject ink into every chamber until the sponge is saturated. A small amount of ink may overflow when full, so be sure to protect the other filling holes on a tri-colour cartridge.

6. With this done do not reattach the label from step 2 as the filling holes help the flow of air into the cartridge.

7. Install the cartridge into your printer again then run a few cleaning cycles from your printer software to pull the ink through. Please check your manual if you are unsure how to do this. Alternatively place the head of the cartridge on a damp spot of some folded kitchen tissue for a minute or so to draw ink out.

You should now be all set to start printing again with your refilled cartridge. If your cartridge does not print correctly we recommend leaving it for a few hours or even overnight to give the ink chance to settle.

With the majority of refilled cartridge the unit will still warn that it is low on ink. With the exception of Lexmark cartridges marked “Return Programme Cartridge” this will not stop you printing however and any warning can simply be ignored until your ink runs out again.

I hope you have found this article helpful. If you have any questions or anything to add please let us know below.

About thangletoan

Hallo Aloha

Posted on 24/03/2012, in bơm mực cho máy in phun màu, canon PiXma MP280, Công nghệ và Giáo dục, Giác ngộ giáo dục, Giác ngộ giáo dục, Đổ mực. Bookmark the permalink. Để lại bình luận.

Gửi phản hồi

Mời bạn điền thông tin vào ô dưới đây hoặc kích vào một biểu tượng để đăng nhập:

WordPress.com Logo

Bạn đang bình luận bằng tài khoản WordPress.com Log Out / Thay đổi )

Twitter picture

Bạn đang bình luận bằng tài khoản Twitter Log Out / Thay đổi )

Facebook photo

Bạn đang bình luận bằng tài khoản Facebook Log Out / Thay đổi )

Google+ photo

Bạn đang bình luận bằng tài khoản Google+ Log Out / Thay đổi )

Connecting to %s

%d bloggers like this: